[PR] Gain and Get More Likes and Followers on Instagram.

#rebateplane

167 posts

TOP POSTS

Rebate shavings are just the best..... #handtools #unplugged #woodshavings #rebateplane #woodenplane

For #woodshavingwednesday I'd like to share the shavings from my glued up cherry scrap #rebateplane #rabbetplane what a treat to use.

Drilled through and cut the bed and breast on the table saw with a thin kerf blade.
#rabbetplane #planemaking #toolmaker #handtools #rebateplane

Tuned up a 50 year old untouched #stanleyno78 #rebateplane , love that whistle as she goes 😃 #woodshavingwednesday #oak #woodworking

I made this rebate / shoulder plane back in 2006. In between my first and second year studying a City & Guilds in cabinetmaking. The body is Jarrah with an ebony sole and a 3/4" @hntgordon blade bedded at 60°. Most of it was made on a workmate workbench in a tiny backyard of a Stoke Newington flat. Still works pretty well 😊
.
#woodwork #rebateplane #shoulderplane #shopmade #handmade #handtool #handtools #handtoolwork #jarrah #ebony #woodworking #furnituremaker #furnituremaking #furnitureworkshop #throwback

New experience. Making rebates freehand, and creates nice little curls.
I must confess that I felt tempted to bring out the No78, which has fence and depth stop, but I finished them with this one.
#woodworking #rebateplane

And now for something pig ugly 😳two iron rebate planes. LH one 5/8" wide with some wood infill at the heel and the iron held by a screw. RH one 1/4" wide, no infill and an iron wedge. A few holes, some threaded. I suspect these were made to attach to some sort of fence or device. If anyone has any ideas I'd love to know. #handtoolthursday #rebateplane #uglytool #handmadetool

She works! No fence, so I used my fingers for now. Suppose I could have anchored my test piece but I was too anxious to get started. #woodworking #woodenplane #rebateplane #handmade

MOST RECENT

The planks on a clinker boat slowly fade from overlapping to flush at the stem and transom, to achieve this we cut half laps on the ends of the plank to correspond to the joints on the plank below and above here’s how I cut mine. It takes seconds and is the same every time, I don’t even clamp the plank, just sit on it and get it done.

My two girls are just gonna sit on the bench for a few more days... stitches out earlier today and hopefully back in the shop on the weekend :)

This isn't the most flattering photo but I wanted to share what you should do if your tenons are a little bit tight in the width. All you need to do is take a rebate plane and put a fence on the shoulder line then plane away. #wood #woodworking #plane #handplane #mortiseandtenon #joinery #handmade #handtools #rebateplane #stanley #woodcraft #finewoodworking

Check out this cool little plane #old #tools #stanley #plane #handplane #stanlyplane anyone know anything about these? How old? #madeinEngland #no75 #rebateplane #rabbetplane

Rebate shavings are just the best..... #handtools #unplugged #woodshavings #rebateplane #woodenplane

Fine tuning some rebates this morning with my @lienielsentoolworks side rebate plane.

And now for something pig ugly 😳two iron rebate planes. LH one 5/8" wide with some wood infill at the heel and the iron held by a screw. RH one 1/4" wide, no infill and an iron wedge. A few holes, some threaded. I suspect these were made to attach to some sort of fence or device. If anyone has any ideas I'd love to know. #handtoolthursday #rebateplane #uglytool #handmadetool

#love this #veritas #rabbitplane or #rebateplane if you rather... it's just the thing to trim these #boxes... #tiny little 6 mm number, one of my #favouritethings in my #workshop ❤️

Contrasting square, and skewed intermittent lignum boxing. #handtools #unplugged #planemaking #planemaker #woodenplane #rebateplane

The skewed, and square rebate planes are now boxed, oiled, and cutting wood . I still need to fine tune them a bit, but so far so good.
#handtools #unplugged #planemaking #planemaker #woodenplane #rebateplane.

Got a call from my older brother's best friend (so sort of my second older brother) Ken, @elliottflooring, with an emergency flooring install problem.
He had some transitional pieces that weren't cut properly and he needed them fixed ASAP.
Because all of the other profiling was already done, it wouldn't have been an easy task to fix it with power tools, so he wanted to know if I could do it with hand tools.
The gist of it was that he needed about 1/8" removed from the middle section.
Yep, I could do it, I told him.
So he dropped it off last night. I got out my Stanley No78 and went at it.
The pieces were 9' long and I only have a 7' bench, so I had to do it in sections.
Still, it didn't take too long to sort out.
And I'm not sure I need to explain how good it feels that a) my friend comes to me to solve such a problem and b) I was able to solve said problem with relative ease.
I should point out that I had the 78 set to take some pretty heavy shavings because I didn't want to take all night.
#handtoolsforthewin #woodwork #woodworking #thekiltedwoodworker #kiltedwoodworker #kiltedwoodworking #stanley78 #rebateplane #rabbetplane

More lignum intermittent boxing.
I have now moved onto the skewed rebate plane. Dovetailed boxing at a 22 1/2 degree skew . I'm beginning to see why this detail went out of fashion! This procedure would be so much easier with a mill or a router, but where would the fun be in that....
#handtools #unplugged #planemaking #planemaker #woodenplane #rebateplane

First piece of intermittent lignum boxing in place on the rebate plane builds
#handtools #planemaking #planemaker #woodenplane #rebateplane

It's amazing what a difference a few chamfers, gouge cuts, and a shaped wedge make to the overall appearance of a plane. The rebate build continues. .....
#handtools#unplugged #planemaking #planemaker #woodenplane #18century #oldwoodplanes #rebateplane

For goodness sake, how many tools do I really need?, I'm only making a rebate plane!
#planemaking #planemaker #woodenplane #18century #oldwoodplanes #rebateplane

Cutting the volute on the rebate planes.
I started this process by boring a hole with a 7/8" centre bit, then enlarged it with carving gouges, rasps and knives.
#planemaking #planemaker #woodenplane #18century #oldwoodplanes #rebateplane

The square, and skewed rebate planes are now marked out, and templates made from originals for the throat cut outs. It was interesting to find that all the examples I measured had two common features. They were all pitched at 47 1/2 degrees, and the center of bed was always dead center of the stock, regardless of the plane length. The skew angle was also constant at 22 1/2 degrees.
#planemaking #planemaker #woodenplane #18century #oldwoodplanes #rebateplane

Most Popular Instagram Hashtags